QuickSpecs
HPE ProLiant DL365 Gen11 - Carrier Grade Supplement QuickSpecs
Table of Contents
NEBS Level 3 and ETSI Certified
This section lists some of the steps required to configure a Factory Integrated Model compliant with typically requested telecom carrier NEBS and ETSI requirements.
Overview
In addition to the worldwide compliance criteria applied to the commercial version of the product, all components listed in this document have been evaluated to the following criteria: SR-3580, Level 3, NEBS Criteria Levels.
- – GR-1089-CORE, EMC & Electrical Safety
- – GR-63-CORE, Physical Protections
- – GR-3108-CORE Outside Plant
- – ETSI EN 300 386, Class A, EMC
- – ETSI EN 300 019-2-1, Class 1.2, Storage
- – ETSI EN 300 019-2-2, Class 2.3, Transportation
- – ETSI EN 300 019-2-3, Class 3.1 & 3.1E, Stationary use at weather protected locations
- – ETSI 300 132, Power supply interface to telecom equipment, -48VDC
- – ETSI ETS 300 753, Acoustic noise
To ensure only valid configurations are ordered, Hewlett Packard Enterprise recommends the use of an HPE approved configurator. Contact your local sales representative for information on configurable product offerings and requirements.
Factory Integrated Models must start with a CTO Server. FIO indicates that this option is only available as a factory installable option. All Factory Integrated Models will be populated with sufficient hard drive blanks based on the number of initial hard drives ordered with the server. Some options may not be integrated at the factory. Contact your local sales representative for additional information.
Notes:
- – To yield a carrier grade server that is compliant with all the required technical criteria, the product content is limited to what is listed in this document. In addition to this, the system maintenance switch #10 must be turned to the "ON" position to enable the expanded operating temperature range and hardware from the following kits MUST be installed:
- HPE ProLiant DL365 Gen11 Low Profile Secondary NEBS-compliant FIO Riser Kit (P71858-B21).
Please refer to the HPE DL365 Gen11 Carrier Grade Conversion documentation on the HPE web site:
Configuration Information
This section lists some of the steps required to configure a Factory Integrated Model.
To ensure valid configurations are ordered, Hewlett Packard Enterprise recommends the use of an HPE approved configurator. Contact your local sales representative for information on configurable product offerings and requirements.
- – Factory Integrated Models must start with a CTO Server.
- – FIO indicates that this option is only available as a factory installable option.
Some options may not be integrated at the factory. Contact your local sales representative for additional information.
Step 1: Base Configuration (choose one of the following configurable models)
| CTO Server | HPE ProLiant DL365 Gen11 - Carrier Grade Supplement 8SFF CTO Server |
|---|---|
| SKU Number | P53933-B21 |
| Processor | Not included as standard |
| DIMM Slots | 24-DIMM slots |
| Storage Controller | Choice of HPE OCP or PCIe plug-in controller |
| PCIe | 1 PCIe x16 Primary Riser |
| Drive Cage - included | 8 SFF (Backplane is not included) |
| Network Controller | Choice of OCP and stand-up card |
| Fans | Not included as standard |
| Management | Default: HPE iLO Standard with Intelligent Provisioning, HPE OneView Standard (requires download), HPE Compute Ops Management (subscription included) |
| USB | Front: 1x USB 3.2 Gen1 + 1x iLO service port Rear: 2x USB 3.2 Gen1 Internal: 2x USB 3.2 Gen1 |
Step 2: Choose Required Options (only one of the following unless otherwise noted)Please select one –B21 processor required below. For second processor, please select the same processor model with –B21 from Core Options – HPE Processors section. | |
| Notes: – Mixing of two different processor models is NOT allowed. For example: first processor, select P53696-B21 then for second processor, select P53696-B21 as well. – Processor kits don’t include heat sink and fans. | |
| Step 2a: Choose Processors | |
| Processor Option Kits – 4th Gen AMD EPYC 9004 Series | |
| AMD EPYC 9124 3.0GHz 16-core 200W Processor for HPE | P53702-B21 |
| AMD EPYC 9224 2.5GHz 24-core 200W Processor for HPE | P58540-B21 |
| AMD EPYC 9354 3.25GHz 32-core 280W Processor for HPE | P53701-B21 |
| AMD EPYC 9554 3.1GHz 64-core 360W Processor for HPE | P53700-B21 |
| AMD EPYC 9654 2.4GHz 96-core 360W Processor for HPE | P53696-B21 |
| AMD EPYC 9534 2.45GHz 64-core 280W Processor for HPE | P53699-B21 |
| AMD EPYC 9634 2.25GHz 84-core 290W Processor for HPE | P53705-B21 |
| AMD EPYC 9254 2.9GHz 24-core 200W Processor for HPE | P53707-B21 |
| AMD EPYC 9454 2.75GHz 48-core 290W Processor for HPE | P53708-B21 |
| AMD EPYC 9334 2.7GHz 32-core 210W Processor for HPE | P53712-B21 |
| Processor Option Kits – 5th Gen AMD EPYC 9005 Series | |
| AMD EPYC 9115 2.6GHz 16-core 125W Processor for HPE | P72659-B21 |
| AMD EPYC 9535 2.4GHz 64-core 300W Processor for HPE | P72652-B21 |
| AMD EPYC 9655 2.6GHz 96-core 400W Processor for HPE | P72650-B21 |
| AMD EPYC 9645 2.3GHz 96-core 320W Processor for HPE | P72649-B21 |
| AMD EPYC 9745 2.4GHz 128-core 400W Processor for HPE | P72648-B21 |
| AMD EPYC 9825 2.2GHz 144-core 390W Processor for HPE | P72647-B21 |
| AMD EPYC 9845 2.1GHz 160-core 390W Processor for HPE | P72646-B21 |
| Step 2b: Choose Memory Options Please select one or more memory from below. For new Gen11 memory population rule whitepaper and optimal memory performance guidelines, please go to Server memory population rules for HPE ProLiant Gen11 servers with AMD EPYC 9004 series processors For additional information, please see the HPE DDR5 Smart Memory QuickSpecs. | |
| Registered DIMMs (RDIMMs) | |
| 4800 MT/s DIMMs supported on 4th Gen AMD EPYC Processors | |
| HPE 16GB (1x16GB) Single Rank x8 DDR5-4800 CAS-40-39-39 EC8 Registered Smart Memory Kit | P50309-B21 |
| HPE 32GB (1x32GB) Dual Rank x8 DDR5-4800 CAS-40-39-39 EC8 Registered Smart Memory Kit | P50311-B21 |
| HPE 64GB (1x64GB) Dual Rank x4 DDR5-4800 CAS-40-39-39 EC8 Registered Smart Memory Kit | P50312-B21 |
| 6400 MT/s DIMMs supported on 5th Gen AMD EPYC Processors | |
| HPE 16GB (1x16GB) Single Rank x8 DDR5-6400 CAS-52-52-52 EC8 Registered Smart Memory Kit | P64984-B21 |
| Notes: – Mixing of x4 & x8 memory is not allowed. – For more detailed information regarding memory population rules, please visit | |
| Memory Blank Kit | |
| HPE DDR4 DIMM Blank Kit | P07818-B21 |
| Notes: DIMM blank kit cannot be selected when 24 DIMMs are ordered. | |
| Step 2c: Choose Power Supplies Select one or two power supplies from below. | |
| Notes: Mixing of two different power supplies is NOT allowed. | |
| HPE Flex Slot Power Supplies | |
| HPE 1600W Flex Slot Platinum Hot Plug Low Halogen Power Supply Kit | P38997-B21 |
| HPE 1600W Flex Slot -48VDC Hot Plug Power Supply Kit | P17023-B21 |
| HPE 1000W Flex Slot Titanium Hot Plug Power Supply Kit | P03178-B21 |
| HPE 800W Flex Slot Platinum Hot Plug Low Halogen Power Supply Kit | P38995-B21 |
| HPE 1600W -48VDC Power Cable Lug Kit | P36877-B21 |
| Notes: – Mixing of different Power Supply SKUs is not allowed. – 1600W -48VDC PSU requires 1x HPE 1600W DC PSU power lug option kit or HPE 1600W DC PSU Power Cable Kit. – Prior to making a power supply selection it is highly recommended that the HPE Power Advisor is run to determine the right size power supply for your server configuration. The HPE Power Advisor is located at: http://www.hpe.com/info/poweradvisor. – HPE ProLiant servers ship with an IEC-IEC power cord used for rack mounting with Power Distribution Units (PDUs). Visit HPE power cords for a full list of optional power cords. | |
| Step 2d: Choose Backplane If front drives are needed in the server, please select one backplane from list below | |
| HPE ProLiant DL365 Gen11 8SFF Tri-Mode U.3 x1 BC FIO Backplane Kit | P55020-B21 |
Step 3: Choose Additional Factory Integratable OptionsOne of the following from each list may be selected if desired at time of factory integration | |
| System Insight Display Options | |
| HPE ProLiant DL365 Gen11 SFF System Insight Display Module Kit | P56924-B21 |
| Notes: Only quantity of one can be supported. | |
Core Options
Step 4: Choose additional options for Factory Integration from Core and Additional Options sections below
Some options may not be integrated at the factory. To ensure only valid configurations are ordered, Hewlett Packard Enterprise recommends the use of a Hewlett Packard Enterprise approved configurator. Contact your local sales representative for additional information.
For more information, visit the HPE Compute Ops Management QuickSpecs:
https://www.hpe.com/psnow/doc/a50004263enw
Supported Servers – CTO only. No OEM. – Complete list can be found here: Latest Supported Server List:
HPE Unique Options | |
| Riser Kits | |
| The CTO or BTO server has 1x Primary riser by default. Here are the additional risers available to select | |
| HPE ProLiant DL365 Gen11 Low Profile Secondary NEBS-compliant FIO Riser Kit | P71858-B21 |
Cooling Options | |
| HPE ProLiant DL3X5 Gen11 1U CPU Performance Heat Sink Kit | P58457-B21 |
| HPE ProLiant DL3XX Gen11 1U Performance Fan Kit | P58462-B21 |
HPE Optical Drives and Option Kit | |
| HPE 9.5mm SATA DVD-ROM Optical Drive | 726536-B21 |
| HPE 9.5mm SATA DVD-RW Optical Drive | 726537-B21 |
| HPE ProLiant DL365 Gen11 2SFF Display Port ODD Blank Kit | P56899-B21 |
| Notes: – Maximum 1 Optical Drive is supported. – ODD needs selection of a HPE DL365 Gen11 2SFF DP ODD Blank Kit. | |
| Essential RAID Controllers | |
| HPE Smart Array E208e-p SR Gen10 (8 External Lanes/No Cache) 12G SAS PCIe Plug-in Controller | 804398-B21 |
| Tri-mode RAID Controllers | |
| HPE MR216i-o Gen11 x16 Lanes without Cache OCP SPDM Storage Controller | P47789-B21 |
| HPE MR408i-o Gen11 x8 Lanes 4GB Cache OCP SPDM Storage Controller | P58335-B21 |
| HPE MR416i-o Gen11 x16 Lanes 8GB Cache OCP SPDM Storage Controller | P47781-B21 |
| HPE MR216i-p Gen11 x16 Lanes without Cache PCI SPDM Plug-in Storage Controller | P47785-B21 |
| HPE MR416i-p Gen11 x16 Lanes 8GB Cache PCI SPDM Plug-in Storage Controller | P47777-B21 |
| HPE SR932i-p Gen11 x32 Lanes 8GB Wide Cache PCI SPDM Plug-in Storage Controller | P47184-B21 |
| Controller Battery Cable Kits | |
| HPE Smart Storage Hybrid Capacitor with 260mm Cable Kit | P02381-B21 |
| HPE 96W Smart Storage Lithium-ion Battery with 260mm Cable Kit | P01367-B21 |
| HPE ProLiant DL3X5 Gen11 Smart Storage Battery 2P 96W Cable Kit | P57884-B21 |
HPE Drives | |
| Enterprise - 12G SAS - SFF Drives | |
| HPE 300GB SAS 12G Mission Critical 15K SFF BC 3-year Warranty Multi Vendor HDD | P28028-B21 |
| HPE 2.4TB SAS 12G Mission Critical 10K SFF BC 3-year Warranty 512e Multi Vendor HDD | P28352-B21 |
| HPE 1.2TB SAS 12G Mission Critical 10K SFF BC 3-year Warranty Multi Vendor HDD | P28586-B21 |
| HPE 300GB SAS 12G Mission Critical 10K SFF BC 3-year Warranty Multi Vendor HDD | P40430-B21 |
| HPE 900GB SAS 12G Mission Critical 15K SFF BC 3-year Warranty Multi Vendor HDD | P40432-B21 |
| HPE 600GB SAS 12G Mission Critical 15K SFF BC 3-year Warranty Multi Vendor HDD | P53560-B21 |
| HPE 600GB SAS 12G Mission Critical 10K SFF BC 3-year Warranty Multi Vendor HDD | P53561-B21 |
| HPE 1.8TB SAS 12G Mission Critical 10K SFF BC 3-year Warranty 512e Multi Vendor HDD | P53562-B21 |
SSD Selection | |
| Read Intensive - 12G SAS - SFF - Solid State Drives | |
| HPE 960GB SAS 12G Read Intensive SFF BC Value SAS Multi Vendor SSD | P40506-B21 |
| HPE 1.92TB SAS 12G Read Intensive SFF BC Value SAS Multi Vendor SSD | P40507-B21 |
| HPE 3.84TB SAS 12G Read Intensive SFF BC Value SAS Multi Vendor SSD | P40508-B21 |
| HPE 7.68TB SAS 12G Read Intensive SFF BC Value SAS Multi Vendor SSD | P40509-B21 |
| HPE 960GB SAS 24G Read Intensive SFF BC Multi Vendor SSD | P49029-B21 |
| HPE 1.92TB SAS 24G Read Intensive SFF BC Multi Vendor SSD | P49031-B21 |
| HPE 3.84TB SAS 24G Read Intensive SFF BC Multi Vendor SSD | P49035-B21 |
| Mixed Use - 12G SAS - SFF - Solid State Drives | |
| HPE 960GB SAS 12G Mixed Use SFF BC Value SAS Multi Vendor SSD | P40510-B21 |
| HPE 1.92TB SAS 12G Mixed Use SFF BC Value SAS Multi Vendor SSD | P40511-B21 |
| HPE 3.84TB SAS 12G Mixed Use SFF BC Value SAS Multi Vendor SSD | P40512-B21 |
| HPE 800GB SAS 24G Mixed Use SFF BC Multi Vendor SSD | P49047-B21 |
| HPE 1.6TB SAS 24G Mixed Use SFF BC Multi Vendor SSD | P49049-B21 |
| HPE 3.2TB SAS 24G Mixed Use SFF BC Multi Vendor SSD | P49053-B21 |
| Mixed Use - 6G SATA - SFF - Solid State Drives | |
| HPE 480GB SATA 6G Mixed Use SFF BC Multi Vendor SSD | P40502-B21 |
| HPE 960GB SATA 6G Mixed Use SFF BC Multi Vendor SSD | P40503-B21 |
| HPE 1.92TB SATA 6G Mixed Use SFF BC Multi Vendor SSD | P40504-B21 |
| HPE 3.84TB SATA 6G Mixed Use SFF BC Multi Vendor SSD | P40505-B21 |
| Read Intensive - 6G SATA - SFF - Solid State Drives | |
| HPE 240GB SATA 6G Read Intensive SFF BC Multi Vendor SSD | P40496-B21 |
| HPE 480GB SATA 6G Read Intensive SFF BC Multi Vendor SSD | P40497-B21 |
| HPE 960GB SATA 6G Read Intensive SFF BC Multi Vendor SSD | P40498-B21 |
| HPE 1.92TB SATA 6G Read Intensive SFF BC Multi Vendor SSD | P40499-B21 |
| HPE 3.84TB SATA 6G Read Intensive SFF BC Multi Vendor SSD | P40500-B21 |
| HPE 7.68TB SATA 6G Read Intensive SFF BC Multi Vendor SSD | P40501-B21 |
| Read Intensive - NVMe - SFF - Solid State Drives | |
| HPE 1.92TB NVMe Gen4 High Performance Read Intensive SFF BC U.3 PM1733a SSD | P50216-B21 |
| HPE 3.84TB NVMe Gen4 High Performance Read Intensive SFF BC U.3 PM1733a SSD | P50219-B21 |
| Mixed Use - NVMe - SFF - Solid State Drives | |
| HPE 1.6TB NVMe Gen4 High Performance Mixed Use SFF BC U.3 PM1735a SSD | P50227-B21 |
| HPE 3.2TB NVMe Gen4 High Performance Mixed Use SFF BC U.3 PM1735a SSD | P50230-B21 |
| HPE 6.4TB NVMe Gen4 High Performance Mixed Use SFF BC U.3 PM1735a SSD | P50233-B21 |
HPE Networking | |
| 1 Gigabit Ethernet adapters | |
| Intel I350-T4 Ethernet 1Gb 4-port BASE-T Adapter for HPE | P21106-B21 |
| Broadcom BCM5719 Ethernet 1Gb 4-port BASE-T Adapter for HPE | P51178-B21 |
| 10 Gigabit Ethernet adapters | |
| Broadcom BCM57416 Ethernet 10Gb 2-port BASE-T Adapter for HPE | P26253-B21 |
| Broadcom BCM57412 Ethernet 10Gb 2-port SFP+ Adapter for HPE | P26259-B21 |
| 10/25 Gigabit Ethernet adapters | |
| Broadcom BCM57414 Ethernet 10/25Gb 2-port SFP28 Adapter for HPE | P26262-B21 |
| Broadcom BCM57504 Ethernet 10/25Gb 4-port SFP28 Adapter for HPE | P26264-B21 |
| Intel E810-XXVDA2 Ethernet 10/25Gb 2-port SFP28 Adapter for HPE | P08443-B21 |
| Mellanox MCX631102AS-ADAT Ethernet 10/25Gb 2-port SFP28 Adapter for HPE | P42044-B21 |
| Intel E810-XXVDA4 Ethernet 10/25Gb 4-port SFP28 Adapter for HPE | P08458-B21 |
| 100/200 Gigabit Ethernet adapters | |
| Mellanox MCX623106AS-CDAT Ethernet 100Gb 2-port QSFP56 Adapter for HPE | P25960-B21 |
| Intel E810-CQDA2 Ethernet 100Gb 2-port QSFP28 Adapter for HPE | P21112-B21 |
OCP Adapter | |
| 1 Gigabit Ethernet OCP adapters | |
| Intel I350-T4 Ethernet 1Gb 4-port BASE-T OCP3 Adapter for HPE | P08449-B21 |
| Broadcom BCM5719 Ethernet 1Gb 4-port BASE-T OCP3 Adapter for HPE | P51181-B21 |
| 10 Gigabit Ethernet OCP Adapters | |
| Broadcom BCM57416 Ethernet 10Gb 2-port BASE-T OCP3 Adapter for HPE | P10097-B21 |
| 10/25 Gigabit Ethernet OCP adapters | |
| Intel E810-XXVDA2 Ethernet 10/25Gb 2-port SFP28 OCP3 Adapter for HPE | P10106-B21 |
| Mellanox MCX631432AS-ADAI Ethernet 10/25Gb 2-port SFP28 OCP3 Adapter for HPE | P42041-B21 |
| 100/200 Gigabit Ethernet adapters | |
| Intel E810-CQDA2 Ethernet 100Gb 2-port QSFP28 OCP3 Adapter for HPE | P22767-B21 |
HPE InfiniBand | |
| HPE InfiniBand HDR100/Ethernet 100Gb 1-port QSFP56 PCIe4 x16 MCX653105A-ECAT Adapter | P23665-B21 |
| HPE InfiniBand HDR100/Ethernet 100Gb 2-port QSFP56 PCIe4 x16 MCX653106A-ECAT Adapter | P23666-B21 |
| HPE ProLiant DL3X5 Gen11 x16 OCP1 OCP2 2P Upgrade Cable Kit | P57849-B21 |
Additional Options
Some options may not be integrated at the factory. To ensure only valid configurations are ordered, Hewlett Packard Enterprise recommends the use of an HPE approved configurator. Contact your local sales representative for additional information.
Cable Kits | |
| HPE ProLiant DL365 Gen11 8SFF OROC x1 SAS/SATA/NVMe Cable Kit | P56901-B21 |
| Notes: – Maximum quantity of one can be selected per system. – This cable kit supports the HPE DL365 G11 8SFF TM U.3 x1 FIO Backplane Kit and an OROC storage controller. | |
| HPE ProLiant DL36X Gen11 Rear Serial Port Cable Kit | P59431-B21 |
HPE Rail Kits | |
| Notes: – HPE rail kits are designed to work with HPE racks in compliance with industry standard EIA-310-E. In the event a customer elects to purchase a third-party rack for use with an HPE rail kit, any such use is at customer’s own risk. HPE makes no express or implied warranties with respect to such third-party racks and specifically disclaims any implied warranties of merchantability and fitness for a particular purpose. Furthermore, HPE has no obligation and assumes no liability for the materials, design, specifications, installation, safety, and compatibility of any such third-party racks with any rail kits, including HPE rail kits. | |
| HPE DL3XX Gen11 Easy Install Rail 2 Kit | P52351-B21 |
| HPE ProLiant DL300 Gen10 Plus 1U Cable Management Arm for Rail Kit | P26489-B21 |
© Copyright 2026 Hewlett Packard Enterprise Development LP. The information contained herein is subject to change without notice. The only warranties for Hewlett Packard Enterprise products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. Hewlett Packard Enterprise shall not be liable for technical or editorial errors or omissions contained herein.
AMD® and EPYC® are registered trademarks of Advanced Micro Devices Corporation in the U.S. and other countries.
Intel® and Xeon® are registered trademarks of Intel Corporation in the U.S. and other countries.
Microsoft®, Windows®, and Windows Server® are U.S. registered trademarks of the Microsoft group of companies.
For hard drives, 1GB = 1 billion bytes. Actual formatted capacity is less
a50009213enw, 17245 - Worldwide - V3 - 22-September-2025