QuickSpecs
HPE ProLiant DL325 Gen11 - Carrier Grade Supplement QuickSpecs
Table of Contents
NEBS Level 3 and ETSI Certified
This section lists some of the steps required to configure a Factory Integrated Model compliant with typically requested telecom carrier NEBS and ETSI requirements.
Overview
In addition to the worldwide compliance criteria applied to the commercial version of the product, all components listed in this document have been evaluated to the following criteria: SR-3580, Level 3, NEBS Criteria Levels
- – GR-1089-CORE, EMC & Electrical Safety
- – GR-63-CORE, Physical Protections
- – GR-3108-CORE Outside Plant
- – ETSI EN 300 386, Class A, EMC
- – ETSI EN 300 019-2-1, Class 1.2, Storage
- – ETSI EN 300 019-2-2, Class 2.3, Transportation
- – ETSI EN 300 019-2-3, Class 3.1 & 3.1E, Stationary use at weather protected locations
- – ETSI 300 132, Power supply interface to telecom equipment, -48VDC
- – ETSI ETS 300 753, Acoustic noise
To ensure only valid configurations are ordered, Hewlett Packard Enterprise recommends the use of an HPE approved configurator. Contact your local sales representative for information on configurable product offerings and requirements.
Factory Integrated Models must start with a CTO Server. FIO indicates that this option is only available as a factory installable option. All Factory Integrated Models will be populated with sufficient hard drive blanks based on the number of initial hard drives ordered with the server. Some options may not be integrated at the factory. Contact your local sales representative for additional information.
Notes:
– To yield a carrier grade server that is compliant with all the required technical criteria, the product content is limited to what is listed in this document. In addition to this, the system maintenance switch #10 must be turned to the "ON" position to enable the expanded operating temperature range. Select HPE NEBS-compliant FIO Trigger System Setting (P40010-B21) for factory integration. Hardware from the following kits MUST be installed:
- • HPE ProLiant DL3X5 Gen11 1U CPU Performance Heat Sink Kit (P58457-B21)
- • HPE ProLiant DL3XX Gen11 1U Performance Fan Kit (P58462-B21)
Please refer to the HPE DL325 Gen11 Carrier Grade Conversion documentation on the HPE web site: http://www.hpe.com/services/hpsc
Configuration Information
This section lists some of the steps required to configure a Factory Integrated Model. To ensure only valid configurations are ordered, Hewlett Packard Enterprise recommends the use of an HPE approved configurator. Contact your local sales representative for information on configurable product offerings and requirements.
- – Factory Integrated Models must start with a CTO Server.
- – FIO indicates that this option is only available as a factory installable option.
- – All Factory Integrated Models will be populated with sufficient hard drive blanks based on the number of initial hard drives ordered with the server.
- – Some options may not be integrated at the factory. Contact your local sales representative for additional information.
Step 1: Base Configuration (choose one (1) of the following configurable server models from the tables below)
| CTO Server | HPE ProLiant DL325 Gen11 Server 8SFF Configure-to-order Server |
|---|---|
| SKU Number | P54199-B21 |
| TAA SKU | P54199-B21#GTA |
| HPE Trusted Supply Chain | P36394-B21 – Optional |
| Processor | Not included as standard |
| DIMM Slots | 12-DIMM slots |
| Storage Controller | Choice of HPE storage controllers |
| PCIe | 1 PCIe 5.0 x16 Primary Riser |
| OCP3.0 Slot | 2 PCIe 5.0 x8 |
| Drive Cage - included | Not included |
| Network Controller | Choice of either OCP 3.0 or select stand-up network adapters for primary networking selection plus additional/optional stand-up network adapters Notes: No embedded networking |
| Cooling | Choice of Standard, Performance, or Closed-Loop Liquid Cooling Heat Sink Choice of Standard, Performance, or Liquid Cooling Fan Kit |
| Management | Default: HPE iLO Standard with Intelligent Provisioning, HPE OneView Standard (requires download), HPE Compute Ops Management (subscription included) |
| Video | 1 VGA rear |
| USB | Front: 1 USB 3.2 Gen1 + iLO service port Rear: 2 USB 3.2 Gen1 Internal: 2 USB 3.2 Gen1 |
| Security | TPM2.0 (Trusted Platform Module) embedded Notes: Disabled on shipments to China |
| Rail Kit | Optional Easy Install rails and CMA |
| Form Factor | 1U Rack |
| Warranty | 3-year parts, 3-year labor, 3-year onsite support with next business day response. |
| Notes: – HPE offers multiple Trade Agreement Act (TAA) compliant configurations to meet the needs of US Federal Government customers. These products are either manufactured or substantially transformed in a designated country. TAA compliance is only provided when HPE options are included as part of factory integrated orders (CTO). – TAA compliant configuration requires TAA versions of the CTO Server SKUs. – HPE Trusted Supply Chain (P36394-B21) is an optional security upgrade intended for agencies and regulated industries needing enhanced security and compliance needs. Applying this option to a DL325 Gen11 CTO server ensures it is built in the USA in a secured facility by vetted HPE personnel assigned to the manufacturing processes. A multitude of checkpoints/inspections for malicious microcode and counterfeit parts are performed throughout the server build, and additional safeguards are put in place against cyber-exploits throughout the server lifecycle. See “HPE Security” section within this document for more detail and learn more at http://www.hpe.com/security – All CTO servers are Energy Star 3.0 compliant. | |
Step 2: Choose Core Options
- – Choice of 1 Processor model and Heat Sink Kit
- • Requires necessary Heat Sink for different processor wattage.
- – Choice of DDR5 memory options.
- • Requires necessary Fan Kits for different memory configurations and subjects to the recommended system ambient temperature.
- – Choice of Drive cage, Storage Controllers, and Storage Controller Cables
- – Choice of SSD, HDD, and Optical Drive
- – Choice of OS Boot Devices
- – Choice of Riser Cards
- – Choice of Networking options
- • PCIe standup or OCP 3.0. Requires necessary Fan Kits and subjects to the recommended system ambient temperature.
- – Choice of Accelerator options
- – Choice of Power and Cooling options
- – Choice of Security options
- – Choice of Software as a Service Management - HPE Compute Ops Management and HPE OneView
Step 3: Choose Additional Options
- – Choice of Embedded Management
- – Choice of Rail Kits
- – Choice of Rack options
- – Choice of Support Services
Core Options
Choice of Core OptionsProcessor Please select ONE 4th or 5th Generation AMD EPYC Processor 4th Gen AMD EPYC 9004 Series | |
| AMD EPYC 9634 2.25GHz 84-core 290W Processor for HPE | P53705-B21 |
| AMD EPYC 9534 2.45GHz 64-core 280W Processor for HPE | P53699-B21 |
| AMD EPYC 9454P 2.75GHz 48-core 290W Processor for HPE | P53709-B21 |
| AMD EPYC 9334 2.7GHz 32-core 210W Processor for HPE | P53712-B21 |
| AMD EPYC 9354P 3.25GHz 32-core 280W Processor for HPE | P53704-B21 |
| AMD EPYC 9254 2.9GHz 24-core 200W Processor for HPE | P53707-B21 |
| AMD EPYC 9224 2.5GHz 24-core 200W Processor for HPE | P58540-B21 |
| AMD EPYC 9124 3.0GHz 16-core 200W Processor for HPE | P53702-B21 |
| 5th Gen AMD EPYC 9005 Series | |
| AMD EPYC 9535 2.4GHz 64-core 300W Processor for HPE | P72652-B21 |
| AMD EPYC 9115 2.6GHz 16-core 125W Processor for HPE | P72659-B21 |
MemoryPlease select one or more memory from below. For new DDR5 memory, please go to HPE DDR5 Smart Memory QuickSpecs For details on the Memory Population Rules and Guidelines with AMD EPYC 9004 series processors, please go to: https://www.hpe.com/psnow/doc/a50007481enw Notes: – Quantity of memory DIMMs selected per socket must be 1, 2, 4, 6, 8, 10, or 12. – The maximum memory speed and capacity is a function of the memory type, memory configuration, and processor model. – The maximum speed capability of the memory system is governed by the combination of the CPU and any other DIMMs installed in the server. If higher speed DIMMs are installed with a CPU that only supports a lower memory speed, the DIMMs will only run at the (lower) memory speed supported by the processor. Likewise, if memory DIMMs are mixed with slower DIMMs within a server, all DIMMs will run at the slower memory speed. For further information please refer to the Memory Population Rules for your specific server. | |
| Registered DIMMs (RDIMMs) | |
| DDR5-4800 (applies to the 4th Generation AMD® EPYC® Processors) | |
| HPE 16GB (1x16GB) Single Rank x8 DDR5-4800 CAS-40-39-39 EC8 Registered Smart Memory Kit | P50309-B21 |
| HPE 32GB (1x32GB) Dual Rank x8 DDR5-4800 CAS-40-39-39 EC8 Registered Smart Memory Kit | P50311-B21 |
| HPE 64GB (1x64GB) Dual Rank x4 DDR5-4800 CAS-40-39-39 EC8 Registered Smart Memory Kit | P50312-B21 |
| DDR5-6400 (applies to the 5th Generation AMD® EPYC® Processors | |
| HPE 16GB (1x16GB) Single Rank x8 DDR5-6400 CAS-52-52-52 EC8 Registered Smart Memory Kit | P64984-B21 |
StorageDrive cages | |
| HPE ProLiant DL325 Gen11 8SFF x1 Tri-Mode U.3 Backplane Kit | P54999-B21 |
| Notes: – Supports 8 SFF SAS/SATA/ NVMe (U.3) Basic Carrier (BC) Drives. – This drive cage can only be selected with 8SFF CTO Server. – Max = 1. | |
| HPE ProLiant DL325 Gen11 2SFF x4 Tri-Mode U.3 BC Backplane Kit | P56652-B21 |
| Notes: – Supports 2 SFF SAS/SATA/ NVMe (U.3) Basic Carrier (BC) Drives. – This drive cage can only be selected with 8SFF CTO Server. – Max = 1. | |
Storage Controller | |
| HPE Smart Array E208e-p SR Gen10 (8 External Lanes/No Cache) 12G SAS PCIe Plug-in Controller | 804398-B21 |
| HPE MR216i-o Gen11 x16 Lanes without Cache OCP SPDM Storage Controller | P47789-B21 |
| HPE MR408i-o Gen11 x8 Lanes 4GB Cache OCP SPDM Storage Controller | P58335-B21 |
| HPE MR416i-o Gen11 x16 Lanes 8GB Cache OCP SPDM Storage Controller | P47781-B21 |
| HPE MR216i-p Gen11 x16 Lanes without Cache PCI SPDM Plug-in Storage Controller | P47785-B21 |
| HPE MR416i-p Gen11 x16 Lanes 8GB Cache PCI SPDM Plug-in Storage Controller | P47777-B21 |
| HPE SR932i-p Gen11 x32 Lanes 8GB Wide Cache PCI SPDM Plug-in Storage Controller | P47184-B21 |
Battery and Hybrid Capacitor | |
| HPE Smart Storage Hybrid Capacitor with 145mm Cable Kit | P02377-B21 |
| HPE 96W Smart Storage Lithium-ion Battery with 145mm Cable Kit | P01366-B21 |
| HPE ProLiant DL325 Gen11 Megacell Extension Cable Kit | P56659-B21 |
Storage Controller Cables | |
| HPE ProLiant DL325 Gen11 8SFF x1 OCP2 Tri-Mode Cable Kit | P59619-B21 |
| Notes: Supports 8 SFF U.3 SAS/SATA/NVMe connecting to storage controllers at OCP22 slot with x1 speed. | |
| HPE ProLiant DL325 Gen11 2SFF x4 OCP2 Tri-Mode Cable Kit | P59620-B21 |
| Notes: Supports 2 SFF U.3 SAS/SATA/NVMe connecting to storage controllers at OCP22 slot with up to x4 speed. | |
HPE Drives | |
| Solid State Drives | |
| For SSD selection guidance, please visit https://ssd.hpe.com/ | |
| Read Intensive - 12G SAS - SFF | |
| HPE 960GB SAS 12G Read Intensive SFF BC Value SAS Multi Vendor SSD | P40506-B21 |
| HPE 1.92TB SAS 12G Read Intensive SFF BC Value SAS Multi Vendor SSD | P40507-B21 |
| HPE 3.84TB SAS 12G Read Intensive SFF BC Value SAS Multi Vendor SSD | P40508-B21 |
| HPE 7.68TB SAS 12G Read Intensive SFF BC Value SAS Multi Vendor SSD | P40509-B21 |
| HPE 1.92TB SAS 24G Read Intensive SFF BC Multi Vendor SSD | P49031-B21 |
| HPE 3.84TB SAS 24G Read Intensive SFF BC Multi Vendor SSD | P49035-B21 |
| Mixed Use - 12G SAS - SFF | |
| HPE 960GB SAS 12G Mixed Use SFF BC Value SAS Multi Vendor SSD | P40510-B21 |
| HPE 1.92TB SAS 12G Mixed Use SFF BC Value SAS Multi Vendor SSD | P40511-B21 |
| HPE 3.84TB SAS 12G Mixed Use SFF BC Value SAS Multi Vendor SSD | P40512-B21 |
| HPE 1.6TB SAS 24G Mixed Use SFF BC Multi Vendor SSD | P49049-B21 |
| HPE 800GB SAS 24G Mixed Use SFF BC Multi Vendor SSD | P49047-B21 |
| HPE 3.2TB SAS 24G Mixed Use SFF BC Multi Vendor SSD | P49053-B21 |
| HPE 960GB SAS 24G Read Intensive SFF BC Multi Vendor SSD | P49029-B21 |
| Read Intensive - 6G SATA - SFF | |
| HPE 240GB SATA 6G Read Intensive SFF BC Multi Vendor SSD | P40496-B21 |
| HPE 480GB SATA 6G Read Intensive SFF BC Multi Vendor SSD | P40497-B21 |
| HPE 960GB SATA 6G Read Intensive SFF BC Multi Vendor SSD | P40498-B21 |
| HPE 1.92TB SATA 6G Read Intensive SFF BC Multi Vendor SSD | P40499-B21 |
| HPE 3.84TB SATA 6G Read Intensive SFF BC Multi Vendor SSD | P40500-B21 |
| HPE 7.68TB SATA 6G Read Intensive SFF BC Multi Vendor SSD | P40501-B21 |
| Mixed Use - 6G SATA - SFF | |
| HPE 480GB SATA 6G Mixed Use SFF BC Multi Vendor SSD | P40502-B21 |
| HPE 960GB SATA 6G Mixed Use SFF BC Multi Vendor SSD | P40503-B21 |
| HPE 1.92TB SATA 6G Mixed Use SFF BC Multi Vendor SSD | P40504-B21 |
| HPE 3.84TB SATA 6G Mixed Use SFF BC Multi Vendor SSD | P40505-B21 |
| Read Intensive - NVMe - SFF | |
| HPE 1.92TB NVMe Gen4 High Performance Read Intensive SFF BC U.3 PM1733a SSD | P50216-B21 |
| HPE 3.84TB NVMe Gen4 High Performance Read Intensive SFF BC U.3 PM1733a SSD | P50219-B21 |
| Mixed Use - NVMe - SFF | |
| HPE 1.6TB NVMe Gen4 High Performance Mixed Use SFF BC U.3 PM1735a SSD | P50227-B21 |
| HPE 3.2TB NVMe Gen4 High Performance Mixed Use SFF BC U.3 PM1735a SSD | P50230-B21 |
| HPE 6.4TB NVMe Gen4 High Performance Mixed Use SFF BC U.3 PM1735a SSD | P50233-B21 |
| Hard Disk Drive Enterprise - 12G SAS - SFF Drives | |
| HPE 300GB SAS 12G Mission Critical 15K SFF BC 3-year Warranty Multi Vendor HDD | P28028-B21 |
| HPE 2.4TB SAS 12G Mission Critical 10K SFF BC 3-year Warranty 512e Multi Vendor HDD | P28352-B21 |
| HPE 1.2TB SAS 12G Mission Critical 10K SFF BC 3-year Warranty Multi Vendor HDD | P28586-B21 |
| HPE 300GB SAS 12G Mission Critical 10K SFF BC 3-year Warranty Multi Vendor HDD | P40430-B21 |
| HPE 900GB SAS 12G Mission Critical 15K SFF BC 3-year Warranty Multi Vendor HDD | P40432-B21 |
| HPE 600GB SAS 12G Mission Critical 15K SFF BC 3-year Warranty Multi Vendor HDD | P53560-B21 |
| HPE 600GB SAS 12G Mission Critical 10K SFF BC 3-year Warranty Multi Vendor HDD | P53561-B21 |
| HPE 1.8TB SAS 12G Mission Critical 10K SFF BC 3-year Warranty 512e Multi Vendor HDD | P53562-B21 |
Boot Controllers | |
| HPE ProLiant DL325 Gen11 NVMe/SATA M.2 Enablement Kit | P57014-B21 |
| Read Intensive - 6G SATA - M.2 - Solid State Drives | |
| HPE 480GB SATA 6G Read Intensive M.2 Multi Vendor SSD | P47818-B21 |
| HPE 480GB NVMe Gen3 Mainstream Performance Read Intensive M.2 Multi Vendor SSD | P40513-B21 |
| HPE 960GB NVMe Gen3 Mainstream Performance Read Intensive M.2 Multi Vendor SSD | P40514-B21 |
| HPE 1.92TB NVMe Gen3 Mainstream Performance Read Intensive M.2 Multi Vendor SSD | P40515-B21 |
Factory Configuration Settings | |
| HPE NEBS-compliant FIO Trigger System Setting | P40010-B21 |
| Notes: Selecting this will enable NEBS expanded operating temperature range by turning ON system maintenance switch #10 Risers | |
| HPE ProLiant DL3X5 Gen11 1U x16 Riser Kit | P56915-B21 |
HPE NetworkingPCIe Adapters 1 Gigabit Ethernet adapter | |
| Intel I350-T4 Ethernet 1Gb 4-port BASE-T Adapter for HPE | P21106-B21 |
| Broadcom BCM5719 Ethernet 1Gb 4-port BASE-T Adapter for HPE | P51178-B21 |
| 10 Gigabit Ethernet adapters | |
| Broadcom BCM57416 Ethernet 10Gb 2-port BASE-T Adapter for HPE | P26253-B21 |
| Broadcom BCM57412 Ethernet 10Gb 2-port SFP+ Adapter for HPE | P26259-B21 |
| 10/25 Gigabit Ethernet adapters | |
| Broadcom BCM57414 Ethernet 10/25Gb 2-port SFP28 Adapter for HPE | P26262-B21 |
| Broadcom BCM57504 Ethernet 10/25Gb 4-port SFP28 Adapter for HPE | P26264-B21 |
| Intel E810-XXVDA2 Ethernet 10/25Gb 2-port SFP28 Adapter for HPE | P08443-B21 |
| Mellanox MCX631102AS-ADAT Ethernet 10/25Gb 2-port SFP28 Adapter for HPE | P42044-B21 |
| Intel E810-XXVDA4 Ethernet 10/25Gb 4-port SFP28 Adapter for HPE | P08458-B21 |
| 100/200 Gigabit Ethernet adapters | |
| Mellanox MCX623106AS-CDAT Ethernet 100Gb 2-port QSFP56 Adapter for HPE | P25960-B21 |
| Intel E810-CQDA2 Ethernet 100Gb 2-port QSFP28 Adapter for HPE | P21112-B21 |
| OCP 3.0 Adapter 1 Gigabit Ethernet OCP adapters | |
| Intel I350-T4 Ethernet 1Gb 4-port BASE-T OCP3 Adapter for HPE | P08449-B21 |
| Broadcom BCM5719 Ethernet 1Gb 4-port BASE-T OCP3 Adapter for HPE | P51181-B21 |
| 10 Gigabit Ethernet OCP Adapters | |
| Broadcom BCM57416 Ethernet 10Gb 2-port BASE-T OCP3 Adapter for HPE | P10097-B21 |
| 10/25 Gigabit Ethernet OCP adapters | |
| Intel E810-XXVDA2 Ethernet 10/25Gb 2-port SFP28 OCP3 Adapter for HPE | P10106-B21 |
| Mellanox MCX631432AS-ADAI Ethernet 10/25Gb 2-port SFP28 OCP3 Adapter for HPE | P42041-B21 |
| 100/200 Gigabit Ethernet adapters | |
| Intel E810-CQDA2 Ethernet 100Gb 2-port QSFP28 OCP3 Adapter for HPE | P22767-B21 |
HPE InfiniBand | |
| HPE InfiniBand HDR100/Ethernet 100Gb 1-port QSFP56 PCIe4 x16 MCX653105A-ECAT Adapter | P23665-B21 |
| HPE InfiniBand HDR100/Ethernet 100Gb 2-port QSFP56 PCIe4 x16 MCX653106A-ECAT Adapter | P23666-B21 |
Power and CoolingNotes: Requires one (1) Heat Sink and Seven (7) Fan Kit in the order. | |
| HPE ProLiant DL3X5 Gen11 1U CPU Performance Heat Sink Kit | P58457-B21 |
| HPE ProLiant DL3XX Gen11 1U Performance Fan Kit | P58462-B21 |
Power Supplies | |
| HPE 800W Flex Slot Platinum Hot Plug Low Halogen Power Supply Kit | P38995-B21 |
| HPE 1000W Flex Slot Titanium Hot Plug Power Supply Kit | P03178-B21 |
| HPE 1600W Flex Slot -48VDC Hot Plug Power Supply Kit | P17023-B21 |
| HPE 1600W Flex Slot Platinum Hot Plug Low Halogen Power Supply Kit | P38997-B21 |
| HPE 1600W -48VDC Power Cable Lug Kit | P36877-B21 |
| Notes: Must be selected along with HPE 1600W Flex Slot -48VDC Hot Plug Power Supply Kit (P17023-B21) | |
| Additional Cable Options | |
| HPE ProLiant DL3X5 Gen11 OCP1 Upgrade Cable Kit | P56658-B21 |
| HPE ProLiant DL3X5 Serial Port Enablement Kit | P50887-B21 |
Additional Options
Rail KitsNotes: HPE rail kits are designed to work with HPE racks in compliance with industry standard EIA-310-E. In the event a customer elects to purchase a third-party rack for use with an HPE rail kit, any such use is at customer’s own risk. HPE makes no express or implied warranties with respect to such third-party racks and specifically disclaims any implied warranties of merchantability and fitness for a particular purpose. Furthermore, HPE has no obligation and assumes no liability for the materials, design, specifications, installation, safety, and compatibility of any such third-party racks with any rail kits, including HPE rail kits. | |
| HPE DL3XX Gen11 Easy Install Rail 2 Kit | P52351-B21 |
| HPE ProLiant DL300 Gen10 Plus 1U Cable Management Arm for Rail Kit | P26489-B21 |
Summary of Changes
| Date | Version History | Action | Description of Change |
|---|---|---|---|
| 22-Sep-2025 | Changed | Core Options section was updated. | |
| Added | 5th Gen AMD EPYC Processors and 6400 MT/s DIMMs | ||
| 18-Aug-2025 | Changed | Standard Features section was updated. | |
| 17-Jun-2024 | Changed | Overview and Core Options sections were updated | |
| 06-May-2024 | Changed | Core Options section was updated. | |
| 04-Mar-2024 | New | New QuickSpecs. |
© Copyright 2025 Hewlett Packard Enterprise Development LP. The information contained herein is subject to change without notice. The only warranties for Hewlett Packard Enterprise products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. Hewlett Packard Enterprise shall not be liable for technical or editorial errors or omissions contained herein.
AMD® and EPYC® are registered trademarks of Advanced Micro Devices Corporation in the U.S. and other countries.
Microsoft®, Windows®, and Windows Server® are U.S. registered trademarks of the Microsoft group of companies.
For hard drives, 1GB = 1 billion bytes. Actual formatted capacity is less
a50007030enw, 17140 - Worldwide - V5 - 22-September-2025