QuickSpecs
HPE ProLiant DL110 Gen11 - Carrier Grade Supplement QuickSpecs
Table of Contents
NEBS Level 3 and ETSI Certified
This section lists some of the steps required to configure a Factory Integrated Model compliant with typically requested telecom carrier NEBS and ETSI requirements.
Overview
HPE ProLiant DL110 Gen11 - Carrier Grade Supplement
NEBS Level 3 and ETSI Certified
In addition to the worldwide compliance criteria applied to the commercial version of the product, all components listed in this document have been evaluated to the following criteria: SR-3580, Level 3, and NEBS Criteria Levels
- – GR-1089-CORE, EMC and Electrical Safety
- – GR-63-CORE, Physical Protections
- – GR-3108-CORE Outside Plant
- – ETSI EN 300 386, Class A, EMC
- – ETSI EN 300 019-2-1, Class 1.2, Storage
- – ETSI EN 300 019-2-2, Class 2.3, Transportation
- – ETSI EN 300 019-2-3, Class 3.1 and 3.1E, Stationary use at weather protected locations
- – ETSI 300 132, Power supply interface to telecom equipment, -48VDC
- – ETSI ETS 300 753, Acoustic noise
To ensure only valid configurations are ordered, Hewlett Packard Enterprise recommends the use of an HPE approved configurator. Contact your local sales representative for information on configurable product offerings and requirements.
Factory Integrated Models must start with a CTO Server. FIO indicates that this option is only available as a factory installable option. All Factory Integrated Models will be populated with sufficient hard drive blanks based on the number of initial hard drives ordered with the server. Some options may not be integrated at the factory. Contact your local sales representative for additional information.
Notes: To yield a carrier grade server that is compliant with all the required technical criteria, the product content is limited to what is listed in this document. In addition to this, the system maintenance switch #10 must be turned to the "ON" position to enable the expanded operating temperature range. Select HPE NEBS-compliant FIO Trigger System Setting (P40010-B21) for factory integration.
Please refer to the HPE DL110 Gen11 Carrier Grade Conversion documentation on the HPE web site:
Configuration Information
This section lists some of the steps required to configure a Factory Integrated Model. To ensure only valid configurations are ordered, Hewlett Packard Enterprise recommends the use of an HPE approved configurator. Contact your local sales representative for information on configurable product offerings and requirements
- – Factory Integrated Models must start with a CTO Server.
- – FIO indicates that this option is only available as a factory installable option.
- – Some options may not be integrated at the factory. Contact your local sales representative for additional information.
Step 1: Base Configuration | |
|---|---|
| CTO Server | HPE ProLiant DL110 Gen11 Front Cabled Configure-to-order Server |
| SKU Number | P54277-B21 |
| Processor | Not included as standard; 1 supported |
| Heatsink | Included |
| DIMM Slots | 8-DIMM slots |
| Storage Controller | Embedded SW RAID with Intel VROC SATA for HPE, choice of Intel VROC NVMe for HPE |
| PCIe | X16/x16 FHHL riser included |
| Fans | 7- dual rotor hot plug |
| Management | HPE iLO with Intelligent Provisioning (standard), iLO Advanced and OneView (optional) |
| USB | iLO Front Service Port |
| Mounting | Default: ‘L’ shaped bracket ears- recommended for 2-post rack mounting (includes cage nuts for mounting in square-hole rack Optional: Short Friction Rail Kit- recommended for 4-post rack mounting |
Step 2: Choose Required Options | |
| Step 2a: Choose Processors Please select one processor required below. | |
| Notes: Processors with 185W TDP or higher will require the DIMM Blank kit (P43725-B21) to be selected when all DIMM slots are not fully populated | |
| Processor Options 4th Generation Intel Xeon-Gold | |
| Notes: All SKUs below ship with processor only. Fans and heatsink are included in the CTO server. | |
| Intel Xeon-Gold 5412U 2.1GHz 24-core 185W Processor for HPE | P49618-B21 |
| Intel Xeon-Gold 5415+ 2.9GHz 8-core 150W Processor for HPE | P49597-B21 |
| Intel Xeon-Gold 6426Y 2.5GHz 16-core 185W Processor for HPE | P49598-B21 |
| Intel Xeon-Gold 6434 3.7GHz 8-core 195W Processor for HPE | P49601-B21 |
| Intel Xeon-Gold 5420+ 2.0GHz 28-core 205W Processor for HPE | P49613-B21 |
| Intel Xeon-Gold 6438Y+ 2.0GHz 32-core 205W Processor for HPE | P49615-B21 |
| Intel Xeon-Gold 6438N 2.0GHz 32-core 205W Processor for HPE | P49638-B21 |
| Intel Xeon-Gold 5411N 1.9GHz 24-core 165W Processor for HPE | P49639-B21 |
| Intel Xeon-Gold 5418N 1.8GHz 24-core 165W Processor for HPE | P49640-B21 |
| Intel Xeon-Gold 6421N 1.8GHz 32-core 185W Processor for HPE | P49641-B21 |
| Intel Xeon-Gold 5423N 2.1GHz 20-core 145W Processor for HPE | P66247-B21 |
| Intel Xeon-Gold 6403N 1.9GHz 24-core 185W Processor for HPE | P66243-B21 |
| Intel Xeon-Gold 6423N 2.0GHz 28-core 195W Processor for HPE | P66239-B21 |
| Intel Xeon-Gold 6443N 2.0GHz 32-core 195W Processor for HPE | P66231-B21 |
| Notes: If 5423N Processor is selected, then secondary riser cannot be selected | |
| 4th Generation Intel Xeon-Silver | |
| Notes: All SKUs below ship with processor only. Fans and heatsink are included in the CTO server. | |
| Intel Xeon-Silver 4410Y 2.0GHz 12-core 150W Processor for HPE | P49610-B21 |
| Intel Xeon-Silver 4416+ 2.0GHz 20-core 165W Processor for HPE | P49611-B21 |
| Step 2b: Choose Memory Options Please select one or more memory modules from the options below. For new Gen11 memory population rule whitepaper and optimal memory performance guidelines, please go to: | |
| Registered DIMMs (RDIMMs) | |
| HPE 16GB (1x16GB) Single Rank x8 DDR5-4800 CAS-40-39-39 EC8 Registered Smart Memory Kit | P43322-B21 |
| HPE 32GB (1x32GB) Dual Rank x8 DDR5-4800 CAS-40-39-39 EC8 Registered Smart Memory Kit | P43328-B21 |
| HPE 64GB (1x64GB) Dual Rank x4 DDR5-4800 CAS-40-39-39 EC8 Registered Smart Memory Kit | P43331-B21 |
| HPE 128GB (1x128GB) Quad Rank x4 DDR5-4800 CAS-46-39-39 EC8 Registered 3DS Smart Memory Kit | P43334-B21 |
| Step 2c: Choose Power Supplies Select one or two power supplies from below. | |
| HPE Flex Slot Power Supplies | |
| HPE ProLiant DL110 700W Flex Slot -48VDC Hot Plug Low Halogen Power Supply Kit | P43150-B21 |
| HPE ProLiant DL110 700W Flex Slot Platinum Hot Plug Low Halogen AC Power Supply Kit | P44975-B21 |
| HPE ProLiant DL110 900W – 1000W Titanium Hot Plug Low Halogen AC Power Supply Kit | P54290-B21 |
| Step 2d: Choose Accelerator Options | |
| HPE ProLiant DL110 Gen11 1-port/3-port Auxiliary Power Cable Kit | P64070-B21 |
Step 3: Choose Additional Options | |
| Rail/Ear Kits | |
| HPE 1U Short Friction Rail Kit | 775612-B21 |
| HPE ProLiant DL110 Gen11 Rail Compatible Ear Kit | P58197-B21 |
Core Options
Step 4: Choose additional options for Factory Integration from Core and Additional Options sections below
Some options may not be integrated at the factory. To ensure only valid configurations are ordered, Hewlett Packard Enterprise recommends the use of an HPE approved configurator. Contact your local sales representative for additional information.
HPE Unique Options | |
| Risers | |
| HPE ProLiant DL110 Gen11 x16 FHHL PCIe Secondary Riser Kit | P54288-B21 |
| DDR4 DIMM Blank | |
| HPE ProLiant DL110 Gen10 Plus DDR4 DIMM FIO Blank Kit | P43725-B21 |
| Notes: Required when processor with 185W or greater TDP is selected, and all DIMM slots are not fully populated. DIMM blank kit cannot be selected if Qty=8 of memory is selected. | |
HPE Solid State Drives | |
| For SSD selection guidance, please visit https://ssd.hpe.com/ | |
| Read Intensive - 6G SATA - M.2 - Solid State Media (2280 type) | |
| HPE 480GB SATA 6G Read Intensive M.2 Multi Vendor SSD | P47818-B21 |
| Read Intensive-PCIe/NVMe-M.2- Solid State Media (22110 and 2280 type) | |
| HPE 480GB NVMe Gen3 Mainstream Performance Read Intensive M.2 Multi Vendor SSD | P40513-B21 |
| HPE 960GB NVMe Gen3 Mainstream Performance Read Intensive M.2 Multi Vendor SSD | P40514-B21 |
| HPE 1.92TB NVMe Gen3 Mainstream Performance Read Intensive M.2 Multi Vendor SSD | P40515-B21 |
Factory Configuration Setting | |
| NEBS-Compliant Setting | |
| HPE NEBS-compliant FIO Trigger System Setting | P40010-B21 |
| iLO Common Password | |
| HPE iLO Common Password FIO Setting | P08040-B21 |
| Notes: − Replaces iLO default randomized password by an HPE defined common password. HPE highly recommends changing this password immediately after the initial onboarding process. − Customers who want to choose their own custom iLO default password should use the HPE Factory Express Integration Services | |
HPE Networking | |
| Notes: The DL110 Gen11 CTO chassis does not come with embedded networking. A PCIe or OCP networking adapter must be selected. | |
| 1 Gigabit Ethernet Adapters | |
| Intel I350-T4 Ethernet 1Gb 4-port BASE-T Adapter for HPE | P21106-B21 |
| Broadcom BCM5719 Ethernet 1Gb 4-port BASE-T Adapter for HPE | P51178-B21 |
| 10 Gigabit Ethernet Adapters | |
| Broadcom BCM57416 Ethernet 10Gb 2-port BASE-T Adapter for HPE | P26253-B21 |
| Broadcom BCM57412 Ethernet 10Gb 2-port SFP+ Adapter for HPE | P26259-B21 |
| 10/25 Gigabit Ethernet Adapters | |
| Mellanox MCX631102AS-ADAT Ethernet 10/25Gb 2-port SFP28 Adapter for HPE | P42044-B21 |
| Intel E810-XXVDA4T Ethernet 10/25Gb 4-port SFP28 MCLK Adapter for HPE | P41636-B21 |
| Broadcom BCM57504 Ethernet 10/25Gb 4-port SFP28 Adapter for HPE | P26264-B21 |
| Notes: Includes GNSS module which provides 1pps signal without the need for an external GNSS appliance. Integrated support for frequency, phase, and time-of-day synchronization with Global Navigation Satellite Systems, including GPS, Galileo, GLONASS, BeiDou, and QZSS. | |
| Intel E810-XXVDA4 Ethernet 10/25Gb 4-port SFP28 Adapter for HPE | P08458-B21 |
| Intel E810-XXVDA2 Ethernet 10/25Gb 2-port SFP28 Adapter for HPE | P08443-B21 |
| Broadcom BCM57414 Ethernet 10/25Gb 2-port SFP28 Adapter for HPE | P26262-B21 |
| Notes: The BCM57414 10/25GbE 2-port SFP28 Adapter cannot be installed in Slot 1. Consider this restriction during the total selection of PCIe Cards. | |
| 100 Gigabit Ethernet Adapters | |
| Intel E810-2CQDA2 Ethernet 100Gb 2-port QSFP28 Adapter for HPE | P41611-B21 |
| Intel E810-CQDA2 Ethernet 100Gb 2-port QSFP28 Adapter for HPE | P21112-B21 |
| Mellanox MCX623106AS-CDAT Ethernet 100Gb 2-port QSFP56 Adapter for HPE | P25960-B21 |
| 1 Gigabit Ethernet OCP Adapters | |
| Intel I350-T4 Ethernet 1Gb 4-port BASE-T OCP3 Adapter for HPE | P08449-B21 |
| Broadcom BCM5719 Ethernet 1Gb 4-port BASE-T OCP3 Adapter for HPE | P51181-B21 |
| 10 Gigabit Ethernet OCP Adapters | |
| Broadcom BCM57416 Ethernet 10Gb 2-port BASE-T OCP3 Adapter for HPE | P10097-B21 |
| Broadcom BCM57412 Ethernet 10Gb 2-port SFP+ OCP3 Adapter for HPE | P26256-B21 |
| 10/25 Gigabit Ethernet OCP Adapters | |
| Intel E810-XXVDA2 Ethernet 10/25Gb 2-port SFP28 OCP3 Adapter for HPE | P10106-B21 |
| Intel E810-XXVDA4 Ethernet 10/25Gb 4-port SFP28 OCP3 Adapter for HPE | P41614-B21 |
| Mellanox MCX631432AS-ADAI Ethernet 10/25Gb 2-port SFP28 OCP3 Adapter for HPE | P42041-B21 |
| Broadcom BCM57414 Ethernet 10/25Gb 2-port SFP28 OCP3 Adapter for HPE | P10115-B21 |
| Broadcom BCM57504 Ethernet 10/25Gb 4-port SFP28 OCP3 Adapter for HPE | P26269-B21 |
| 100 Gigabit Ethernet OCP Adapters | |
| Intel E810-CQDA2 Ethernet 100Gb 2-port QSFP28 OCP3 Adapter for HPE | P22767-B21 |
| Notes: – Max=1 OCP card can be selected. This is inclusive of all OCP categories and sub-categories. – Does not consume PCIe slot | |
© Copyright 2026 Hewlett Packard Enterprise Development LP. The information contained herein is subject to change without notice. The only warranties for Hewlett Packard Enterprise products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. Hewlett Packard Enterprise shall not be liable for technical or editorial errors or omissions contained herein.
Intel® and Xeon® are registered trademarks of Intel Corporation in the U.S. and other countries.
Microsoft®, Windows®, and Windows Server® are U.S. registered trademarks of the Microsoft group of companies.
For hard drives, 1GB = 1 billion bytes. Actual formatted capacity is less
a50009221enw, 17253 - Worldwide - V2 - 03-November-2025